Jetcat P220-RXi Turbine Engine - Thrust: 48.5 lb
Move your mouse over image or click to enlarge

Jetcat P220-RXi Turbine Engine - Thrust: 48.5 lb

Weight:

SKU:

Barcode:

Collections: All, Turbine Engines

Product type:

Vendor: Global Jet Club JC

Tags: Jet Cat, Jetcat, P220-RXi, RC Turbine Engine, Turbine Engines

Availability:

$4,195.00

Jetcat P220-RXi - Thrust: 48.5 lb, Now Features a Brushless Fuel Pump
Now includes an integrated brushless pump, brushless starter/generator, charging system for turbine battery and optional charging system for receiver battery.

The newly developed JetCat P220 RXi, not only has an integrated brushless and fully encapsulated fuel pump, but also features a brushless starter / generator system!

Jetcat P220-RXi turbine engine, made in Germany
MSRP Retail $4,195.00

Specifications:

  • Maximum Thrust: 220N @ 48.5 lbs
  • Thrust: 220N at 117.000 rpm
  • Thrust at idle: 9N
  • Weight: 1850g incl. Starter and Generator
  • Diameter: 116,8mm
  • Length in total: 309mm
  • Rpm range: 35,000 - 117,000 rpm
  • Exhaust temperature: max. 750°C
  • Fuel consumption: 725ml/min (Full throttle)
  • Fuel: Jet A1, Kerosene, Petroleum
  • Lubrication: appr. 5% of turbine oil mixed in Fuel

Maintenance cycle: every 25 hours Cost: $300

Jetcat P220-RXi includes:

The future is here! The rotor of the fuel pump is running in the fuel, therefore the otherwise necessary shaft seals can be omitted. The starter / generator operates completely mechanical contact free to the turbine shaft. Therefore the "coupling" of starter to engine rotor is resistant to wear and dirt (no slippage of the starter clutch by oil/dirt, no O-ring wear possible)

The specially designed “non-contact coupling system” (patent pending) also ensures that the brushless generator, compared to the engine rotor, only spins at comparably low rpms (well below 10,000 1 / min). This ensures a very high reliability and durability of the entire starter / generator system.

Furthermore, the JetCat P220 RXi has been optimized for a minimal system weight. The housing is made of thin-walled laser welded stainless steel. The entire engine, including integrated brushless pump, valves, fuel filter, generator and charging system only weighs 1850g.

In conjunction with the new “JetCat BMS system” (BMS=Battery Management System) lighter and smaller receiver batteries than previously required can be used. The receiver batteries are constantly recharged via the BMS system as soon as the engine is running.

Never charge batteries, only refuel in the future!

After starting the engine, the engine battery is recharged via the generator with high power. The engine side electronics controls the charging current / voltage automatically.

The engine battery is also charged if the engine runs at idle. The optional JetCat BMS system can be used to also recharge the receiver batteries. In this configuration, the BMS-system ensures that the receiver batteries are always fully charged upon the next engine startup. The charging of the receiver batteries will continue until these are completely full, even if the RC-system of the model should have been powered down.


Now Includes the ECU V10.0

    The updated ECU comprises a high speed digital power bus for control and power supply of all engine peripherals (e.g. engine, fuel pump, solenoids, smoke pump, lighting systems, etc. ) with a minimum of wiring connections.
    An on board precision pressure and ambient temperature sensor allows for optimum engine control, independent to environmental conditions.

Includes JetCat Mini-GSU

The JetCat Mini-GSU is an optional miniature Ground Support Unit (GSU). It comprises a 2x16 character alphanumeric backlit LCD display and 10 control keys.
    Function wise it can be used as a 100% replacement for our normal GSU. Its small form factor and weight makes it ideally suited for permanent installation in the model. Connection to ECU`s up to Version 6.0 is via a 8-pin miniature flatcable connector directly to the LED-I/O interface. Connection to ECUs from Version 10.0 is via a 6-pin miniature flatcable directly to the ECU or the LED-I/O interface or 8-pin flat cable to JetCat I/O-interface with charging option.


      * Fuel tubing, tubing connector set, filters, and cable set
      * Turbine mounting clamp
      * Detailed instruction manual
      * 3 Year warranty

      Why Buy From GlobalJet.Club Instead of Manufacturer?

      • Timezone communication challenges
      • How's your German language speaking skills?
      • We act on your behalf for all customer service.
      • Our volume buying gets you better package deals
      • At event support, we can provide direct help.
      • Save money and frustration, deal directly with GlobalJet.Club